Call Now and Save!
1-866-941-5112

Get 10% off all products! Limited coupons available. Use Coupon "10OFF"

Deluxe Flat Top Plate – 3in X 18in X 18in

deluxe-flat-1

$126.77

SKU: DFTP31818. Category: .

Use this Flex Liner Deluxe Top Plate in order to mount the Top Plate to the existing chimney crown. This Top Plate includes a detachable single flue cap. The liner fits in the hole and is secured to the top plate by tightening the hose clamp band in the inside of the top plate collar.

If you have the old clay Terra-Cotta liner sticking out above the chimney crown you have two options. You can break the old clay tile and make it flush with the top of the chimney crown and mount this flat top plate to the crown, or you can mount a Terra-Cotta Top Plate directly to the old clay liner.

 

Weight 20 lbs
Dimensions 23 × 23 × 23 in

Related Products

  • $101.53

    Deluxe Flat Top Plate – 3in X 8in X 13in

    , ,
  • $109.56

    Deluxe Flat Top Plate – 3in X 13in X 13in

    , ,
  • $93.71

    Deluxe Flat Top Plate – 3in X 8in X 8in

    , ,
  • $115.04

    Deluxe Flat Top Plate – 3in X 13in X 18in

    , ,








    *Note: If you have a terra cotta clay chimney
    flue lining, be sure to measure the true length and width of the
    inside of your chimney flue space.

    *If there is a terra cotta clay flue liner, does it protrude out of
    the top of the chimney at least 2 inches? If there are at least 2
    inches and the terra cotta clay is in good condition, you will use
    our stainless steel, terra cotta top plate that has a 1 1⁄2inch edge
    that goes all the way around (like a shoebox lid).

    *If your terra cotta clay flue is in bad shape at the top, you may
    need to just take a hammer and tap all around that terra cotta,
    taking it away to make the surface flat at the top of your chimney.
    In that case, you will simply use the flat top plate that comes with
    our liner kit.



    *Note: If you have a terra cotta clay chimney
    flue lining, be sure to measure the true length and width of the
    inside of your chimney flue space.

    *If it is on the back of the stove, is it parallel with the back of the stove or is it at an angle, like 45 degrees?

    *If it is at an angle you will use an insert stove adaptor (an insert liner kit) rather than a two-part tee with cleanout cap.


    Usually pellet stoves have an exhaust hole id of 3 inches. However, if you are going up more than 15 feet to the top of your chimney you need to use a pipe and/or flex liner that is 4 inches diameter.





    If you are only venting a hot water heater then the exhaust hole diameter is probably 3 inch diameter. If it is 3 inch diameter and you are going up more than 15 feet to the top of your chimney, you must use a 4 inch diameter flexible liner or ridged pipe for proper draft. We also suggest to go ahead and use a 4 inch diameter flexible liner or ridged pipe even if the total length is 15 feet or less.


    Not the depth or any other dimension inside your fireplace.

    Most gas log fireplaces require an 8 inch liner kit or rigid kit. But do not assume that is the case for the gas log fireplace kit you are installing. Obey the requirements for that specific unit that are in your installation/instruction manual.

    THANK YOU FOR ANSWERING THOSE QUESTIONS

    NOW GIVE US A CALL AND SPEAK WITH ONE OF OUR TECHS

    866-941-5112