Flexible Chimney Flue Pipe can Bring New Life to Your Chimney - Chimney Liner Depot

Aug 9, 2012 admin No Comments

The chimney liner is the ultimate solution to the problems that plague most chimneys. Modern stainless steel provides air tight and water tight barrier that seals in gases and creosote. Underwriters Laboratory declared that flex systems excel standards for chimney safety and can even withstand a chimney fire and still maintain structural integrity.

This system is to be installed in all new or existing masonry chimneys that are used for the natural draft venting of gas, liquid, and solid fuel fired residential type appliances and masonry fireplaces. While extreme care has been taken to make the system as safe as possible, proper installation, operation and maintenance should be followed.

316TI Stainless Steel is the Best Stainless Steel for Chimney Liners
316TI is a stainless steel alloy with a small amount of titanium added. It’s make-up allows it to resist acids and the stresses of hot and cold cycles. It can be used with solid fuels (wood, coal and pellet), gas and oil. It can withstand temperatures up to 2100 degrees.

If your masonry chimney is suffering from problems due to a newer appliance, the solution is to install a stainless steel chimney liner.

Comments are closed.

About Us

Chimney Liner Depot is the number one online wholesaler of flexible and rigid liners. We make our stainless liners and components in-house from the best alloys of stainless steel. We can make any custom chimney part you may need. We offer the best prices on quality stainless steel liners. Cutting out the middle man when buying a liner means you save big money. When you buy a liner from us, you are dealing with a company that knows its products inside and out. Our stainless liners are backed by a lifetime warranty. When you purchase a flue liner from us, you will have peace of mind, once you buy our products you can come back to us for help at any time.

Email

Name

Phone Number (Cell)

Phone Number (Home)

Shipping Address you will want your order shipped to.

What Is The Vertical Measurement From Where Your Liner Will Start
To The Very Top Of Your Chimney?

What Is The (ID) Inside Dimension Of Your Chimney Flue?

*Note: If you have a terra cotta clay chimney
flue lining, be sure to measure the true length and width of the
inside of your chimney flue space.

*If there is a terra cotta clay flue liner, does it protrude out of
the top of the chimney at least 2 inches? If there are at least 2
inches and the terra cotta clay is in good condition, you will use
our stainless steel, terra cotta top plate that has a 1 1⁄2inch edge
that goes all the way around (like a shoebox lid).

*If your terra cotta clay flue is in bad shape at the top, you may
need to just take a hammer and tap all around that terra cotta,
taking it away to make the surface flat at the top of your chimney.
In that case, you will simply use the flat top plate that comes with
our liner kit.

What is the (ID) inside dimension of the exhaust hole or collar?

Is the exhaust hole on the top of the stove or on the back of the stove?

*Note: If you have a terra cotta clay chimney
flue lining, be sure to measure the true length and width of the
inside of your chimney flue space.

*If it is on the back of the stove, is it parallel with the back of the stove or is it at an angle, like 45 degrees?

*If it is at an angle you will use an insert stove adaptor (an insert liner kit) rather than a two-part tee with cleanout cap.

What is the (ID) inside dimension of the exhaust hole or collar?

Usually pellet stoves have an exhaust hole id of 3 inches. However, if you are going up more than 15 feet to the top of your chimney you need to use a pipe and/or flex liner that is 4 inches diameter.

What is the (ID) inside dimension of the exhaust hole or collar?

Are you venting a hot water heater together?

What is the (ID) inside dimension of the exhaust hole or collar of your hot water Heater?

Are you venting a hot water heater only (no furnace or boiler)

If you are only venting a hot water heater then the exhaust hole diameter is probably 3 inch diameter. If it is 3 inch diameter and you are going up more than 15 feet to the top of your chimney, you must use a 4 inch diameter flexible liner or ridged pipe for proper draft. We also suggest to go ahead and use a 4 inch diameter flexible liner or ridged pipe even if the total length is 15 feet or less.

What are the height and width of the opening, front face of your fireplace?

Not the depth or any other dimension inside your fireplace.

Most gas log fireplaces require an 8 inch liner kit or rigid kit. But do not assume that is the case for the gas log fireplace kit you are installing. Obey the requirements for that specific unit that are in your installation/instruction manual.

THANK YOU FOR ANSWERING THOSE QUESTIONS

NOW GIVE US A CALL AND SPEAK WITH ONE OF OUR TECHS